Rockville DBCOMP4 Competition Mono Amplifier 3000W Rms! Car Audio Amp












- Features - Rockville dBcomp4 Competition Mono Amplifier 3000w RMS Dyno-Certified! Car Audio Amp.
- Dyno Certified RMS Power Ratings - (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc). 1 Ohm - 3000 Watts x 1 Channel <1% THD+N at 14.4 volts (83% efficiency). 2 Ohm - 2000 Watts x 1 Channel <1% THD+N at 14.4 volts (80% efficiency). Digital voltage display on amp.
- External 400A fuse. High-Speed MOSFET Power Supply. Optical Coupler Class D Technology. Fully Adjustable 24dB / Octave Crossover with Differential Circuitry. Low Pass Filter - 50Hz - 250Hz. Subsonic Filter - 15Hz - 55Hz. Phase Control Switch. Limiter With ON/OFF Switch (You can turn off the limiter if you want to burp a sub during a competition and get more power out of the amp).
- Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry. Power/Protect/Clip LED Indicators on control panel. Power/Protect/Clip LED Indicators on Remote control. Minimum THD at Rated Power - 90dB. Under Voltage Protection at 10V.
- Over Voltage Protection at 16V. Frequency Response - 15Hz - 250Hz. Damping Factor - >150 @ 100Hz. Dimensions - (W x H x L) 9 inch x 2.4 inch x 23 inch
Nvx XAD-PARENT Xad11 700W Rms 1-Ohm Stable Full Bridge Class D High Power Competition Monoblock Car Audio Mosfet Amplifier









Skar Audio SKV2-4500.1D Monoblock Class D Mosfet Competition Grade Subwoofer Amplifier






- Competition Grade SPL Class D Mono black MOSFET Car Power Amplifier
- Peak Power at 1 Ohm - 7, 400 Watts | RMS Power at 1 Ohm - 4, 500 Watts
- Stable at 1 Ohm, Frequency Response - 15Hz - 270Hz
- Featuring 4-Way Protection Circuitry and Dual 1/0 Gauge Power And Ground Input Terminals for Maximum Current Flow
- User Adjustable Low Pass Filter (Variable) - 35Hz - 250Hz, Remote Subwoofer Level Control Included
Topstronggear CA-TSG AMP 1 Ohm 1500 Watts Class D Full Range Mono Block Amplifier







- Class D MOSFET Mono Block Power Amplifier
- Max Power at 1 Ohm - 1500 WattsMax Power at 2 Ohms - 800 WattsMax Power at 4 Ohms - 510 Watts
- Low Pass Crossover - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
- Remote Subwoofer Level Control Included.Variable Bass Boost - Variable Bass Boost 0 to 12dB(50Hz) allows you to adjust the low bass within the boost range to just the way you like it.
- Warranty - TopstrongGear provides a powerful 1 year Platinum Online Dealer Warranty
Skar Audio 43217-166536 Rp-4500.1D Monoblock Class D Mosfet Amplifier






- Competition Grade Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm - 7, 000 Watts | RMS Power at 1 Ohm - 4, 500 Watts
- Stable at 1 ohm | Remote Subwoofer Level Control Included
- Frequency Response - 20Hz - 250Hz, On-board Bass Boost Control 0-9dB
- Featuring 4-Way Protection Circuitry and 1/0 AWG Power & Ground Input Terminals for Maximum Current Flow
Alpine S-A60M S-Series Class D Mono Amplifier







Blaupunkt AMP1501PRO 1501Pro Car Audio Monoblock 1 Channel 2 Ohm Stable Amp Amplifier 1500 Watts Max









- Powerful Performance - The AMP1501PRO delivers an impressive 563-watt RMS and a maximum output of 1500 watts, providing a significant power boost for a vibrant and dynamic driving soundtrack.
- Space-Efficient Design - With compact dimensions (7.1 inch x 7.5 inch x 2.1"), this amplifier seamlessly integrates into any trunk, optimizing space while delivering high-quality audio performance.
- High-pass and low-pass filters - integrated high- and low-pass filters on the rear panel allow you to set the crossover frequency between the subwoofer and speakers.
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
Recoil DI600.1 Class-D Car Audio Mono-Block Subwoofer Amplifier






- Class-D Mono-block Subwoofer Amplifier, 1200 Watts Max Power, RMS 600 Watts x 1@2Ohm; RMS 350 Watts x 1@4Ohm.
- Featuring a high-speed MOSFET power supply, premium grade internal components, as well as 4-way protection circuitry, the amplifier will safely operate at the highest levels of performance for hours on end. Highly efficient heatsinks keep the amplifier cool with a sophisticated new look.
- Recoil mono amplifiers come with bass remote control. Use it to customize your bass on the fly with just a turn of a knob.
- You'll have full reign over your amplifier with the built-in user control panel, featuring a bass EQ, and variable adjustment tunings for gain level, low-pass filter, and subsonic filter.
- Dimensions - 7.48 inch x 5.90 inch x 1.77 inch
Crunch PZ2-2030.1D Powerzone 2000 Watt Mono Amplifier, Car Audio Amplifier





- MONO AMPLIFIER - With low voltage RCA inputs this mono amplifier produces the highest sound quality connection with quality RCA materials helps prevent interference and minimize distortion in the signal path.
- ELECTRONIC EQUALIZER - Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers.
- UNIVERSAL COMPATIBILITY - Exclusive Crunch SPEED-FET MOSFET components maximize power efficiency while improving sound quality and minimizing distortion and the variable electronic crossovers allow for complete control of the sound
- BASS REMOTE INCLUDED - Wired Bass Remote allows adjustments to bass frequencies from the remote which can be mounted anywhere in the vehicle.
Rockville DBCOMP5+RWK0CU-AM Dbcomp5 Mono Competition Amplifier 3500W Rms! Car Audio Amp Bundle









- Package Includes - (1) Rockville dBcomp5 Mono Competition Amplifier 3500w RMS Dyno-Certified! Car Audio Amp. (1) Rockville RWK0CU 0 AWG Gauge 100% Copper Complete Amp Installation Wire Kit OFC. 0 Gauge Power Amplifier Installation Kit. Designed specifically for car audio systems over 1000 watts RMS to 3000 Watts. Made from silver-tinned 100% virgin copper for a pure uninterrupted transfer of power and signal
- The solid brass gold plated ANL Fuse Holder offers ideal protection for high powered systems. Strand Count - 4704. BC-5W2 Compliant. 17 ft. Frosted Blue 0 gauge power wire with seamless crimp ring terminal. 3 ft. Frosted Gray 0 gauge ground wire. 17 ft. Blue 18 gauge remote lead wire. 25 ft. Frosted Clear/Blue 12 gauge flat speaker wire. 17 ft. Triple shielded twisted pair RCA cables. One ANL Fuse Holder with 250 amp ANL fuse. One 1/2 inch black rubber firewall grommet. Two 0 gauge spade terminals
- Two black 12 gauge nickel-plated spade lugs. Three blue 12 gauge nickel-plated spade lugs. One black 0 gauge ring terminal. Ten 6 inch black zip ties. Includes - Amplifier. Bass Remote. Birth sheet with tested power. Owner's manual. Mounting Screws. Warranty. Features - Rockville dBcomp5 Mono Competition Amplifier 3500w RMS Dyno-Certified! Car Audio Amp
- Dyno Certified RMS Power Ratings - (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc) 1 Ohm - 3500 Watts x 1 Channel <1% THD+N at 14.4 volts (83% efficiency)2 Ohm - 2200 Watts x 1 Channel <1% THD+N at 14.4 volts (80% efficiency). 1 Ohm - 3500 Watts x 1 Channel <1% THD+N at 14.4 volts (83% efficiency). 2 Ohm - 2200 Watts x 1 Channel <1% THD+N at 14.4 volts (80% efficiency). Digital voltage display on amp
- External 350A fuse. High-Speed MOSFET Power Supply. Optical Coupler Class "D" Technology. Fully Adjustable 24dB / Octave Crossover with Differential Circuitry. Low Pass Filter - 50Hz - 250Hz. Subsonic Filter - 15Hz - 55Hz. Phase Control Switch. Limiter ON/OFF Switch. Full IC-Controlled Protection Circuitry. Remote Dashboard Subwoofer Control. Fully Adjustable 12dB Bass Equalizer. Mute and Delay Soft Start System. RCA Preamp Line Output. 8 Volt Preamp Circuitry
Audiozerone ZE500.1 1000W Monoblock Class D Mosfet Subwoofer Audio





- Power - 1000 Watts MAX x 1 @1-Ohm, 500 Watts RMS x 1 @1-Ohm, 350 Watts RMS x 1 @2-Ohms,200 Watts RMS x 1 @4-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until its needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
- To keep both your car and the stereo amp safe, this ZE500.1 is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality sound in a sturdy form factor
- Specs - Dimensions - 7.5 x 6.9 x2, Weight 3.51 lbs.
Skar Audio RP-1200.1D Monoblock Class D Mosfet Amplifier





- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm - 1,600 Watts | RMS Power at 1 Ohm - 1,200 Watts
- Frequency Response - 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow. Damping Factor - 150<
- Stable at 1 ohm | Remote Subwoofer Level Control Included
- Highly Efficient Heatsink Design allows for Maximum Reliability & Performance
Hifonics ZRX1216.1DV2 Zeus Zrx V2 1200W Class D Mono Amplifier






- POWERFUL PERFORMANCE - The Hifonics amplifier delivers exceptional power for your car audio system. This class D amplifier boasts up to 1200 watts of output, making it ideal for driving subwoofers and speakers with clarity and precision. The mono amplifier car audio design ensures optimal performance for bass-heavy sound systems, providing the punch and depth you crave in your music.
- EFFICIENT CLASS D TECHNOLOGY - Featuring cutting-edge Class D topology, this Hifonics amp combines high efficiency with big power in a compact footprint. The PWM MOSFET power supply maintains stable voltage through Ultra-Fi MOSFET output devices, resulting in consistent performance and minimal heat generation. Experience superior sound quality without sacrificing space in your vehicle.
- ADVANCED COOLING AND PROTECTION - The amplifier car audio unit features an old-school Hifonics aluminum heat sink for superior heat dissipation, ensuring reliable operation even during extended use. LED system protection circuitry diagnostics monitor overload and speaker short protection, with illuminated indicators on the end panel for easy troubleshooting and peace of mind.
- CUSTOMIZABLE SOUND - Fine-tune your audio experience with the onboard electronic crossover and equalizer. This monoblock amplifier car audio device allows you to control specific frequencies, tailoring the output to your speakers and subwoofers. The included bass remote gives you convenient control over your low-end sound, letting you adjust on the fly for the perfect bass response.
- UNIVERSAL COMPATIBILITY AND EASY INSTALLATION - This Hifonics monoblock amplifier is designed for universal fitment, making it suitable for a wide range of vehicles. Secure, molded connection terminals for power, ground, and speaker connections are angled for easy access and clean wire management. Nickel-plated, high-temperature resistant RCA inputs with hex screw terminals ensure secure, erosion-resistant connections.
Autotek TA-1155.1 1100 Watts Ta Mono Subwoofer Car Audio Amplifier.







Boss Audio Systems R1100M Monoblock Car Amplifier






- Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms
- Class A/B Topology - Class A amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class B amplifiers have no current flowing through its outputs with no audio signal
- MOSFET Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
- Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
- Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- Switchable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
- Variable Input Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier
- Specs - Dimensions - 9.13 x 10.44 x 2.25, Weight - 4.43 lbs., Speaker Impedance - 2 to 8 Ohm, THD @ RMS Output - 0.01%, S/N Ratio - 102 dB, Frequency Response - 9 Hz to 50 kHz, Fuse Quantity - 1 30 Amp ATO Blade
- BOSS Audio Systems provides a 6 Year Platinum Online Dealer Warranty for purchases through Amazon.Com. We strongly encourage professional installation of this product to ensure proper functionality
Kicker 49WXZ36001 Warhorse 49Wxa3600.1 Mono Competition Amplifier









- Features extreme reliability under intense bass power and overall use
- Full-bridge Class-D design
- Quad micro-controller-regulated cooling fans
- Capable of daisy-chaining remote power across multiple amps
- Competition mode switch to avoid potentiometer creep, fix crossover setting, and gain-match multiple amps
- Includes premium remote bass-level control with a magnetic mount
- Includes a heavy-duty, magnetic-mount diagnostic tool for monitoring voltage measurements and amp protection status
- Fully compatible with most factory or aftermarket source units (with FIT+ differential inputs)
- Bespoke design engineered completely in-house by KICKER R&D
- RMS Power @ 1-ohm - 3,600 Watts; RMS Power @ 2-ohm - 2,500 Watts; RMS Power @ 4-ohm - 1,400 Watts; Dynamic RMS Power - 5,000 Watts; Frequency Response - 10-200 Hz; Signal-To-Noise Ratio - >90 dB; Input Sensitivity - 125mV - 40V; Variable Low-Pass Crossover - 50-200 Hz @ 24 dB; Subsonic Filter - 15 Hz @ 24 dB & OFF; Dimensions - Height 2-9/16"(6.35mm), Width 9-1/8"(23.2mm), Length 15-3/8"(39.1mm)
Nvx NDA12001 2400W Peak (1200W Rms) N-Series Class-D 1-Ohm Stable Monoblock Amplifier





- High Power Output - Delivers an impressive 2400W peak power and 1200W RMS at 1-ohm for powerful, clear audio, ensuring an immersive listening experience.
- Versatile Connectivity - Features speaker-level (high-level) inputs with signal sensing remote turn-on and includes a wired bass level remote control for easy adjustments on the go.
- Advanced Protection - Equipped with 4-way protection circuitry, including thermal, overload, speaker short, and DC offset protection, for reliable and safe operation.
- Precision Sound Control - Offers a variable low-pass filter (50 - 250 Hz), subsonic filter (10 - 55 Hz), and adjustable bass boost (0 - 18 dB) for customizable sound shaping.
- Compact Design - Sleek and compact dimensions (9.37 inch L x 4.42 inch W x 1.73 inch H) for easy installation, with a recommended 4 AWG gauge amplifier wiring kit for optimal performance.
Skar Audio SK-M5001D Compact Monoblock Class D Mosfet Car Amplifier







Soundstream TXP16000D Txp1.6000D 6000 Watts Max 1 Ohm Monoblock Class D Tarantula Xtreme Subwoofer Speaker Bass Car Audio Amplifier




- 1-ohm Minimum Impedance Monoblock Operation LED Accent Lighting Illuminates Circuit Board, for Your Viewing Pleasure Silicone Steel Alloy Core Power Supply Transformers, & Flux Capacitors
- Military Grade SMT PCB Maintains Dynamic Performance Direct Short, Thermal, & Overload Circuits Protect Amplifier 200mV-6V High Level or Low-Level RCA Input & Output
- Variable 12dB High Pass, Low Pass, & Subsonic Crossovers Dash Mount Gain Control Module Included
Hifonics HAC-5000.1D 5000 Watt Mono Block Car Audio Amplifier






- COLOSSAL MONO RMS POWER - Delivers an astounding 5000 watts of power with 1 x 5000W @ 1 ohm, 1 x 2500W @ 2 ohms, and 1 x 1250W @ 4 ohms, perfect for driving multiple high-performance subwoofers in competition-level systems.
- EFFICIENT DESIGN - Super D Class amplifier with half-bridge design and fewer components for higher power output and improved efficiency, truly embodying the "POWER FROM THE GODS" concept.
- PRECISE BASS CONTROL - Features variable electronic crossovers (15Hz-1KHz high pass, 50Hz-10KHz low pass), built-in bass control, and 0-12dB bass boost for customized low-frequency performance.
- SUPERIOR BUILD QUALITY - Utilizes Ultra-Fi MOSFETS, multi-layer PCBs, and clean board construction for optimal performance and durability in the most demanding car audio environments.
- PROTECTION & CONVENIENCE - Includes triple protection circuits, delayed turn-on function, and a bass remote for easy adjustments. Full range Class-D chipset ensures compatibility with a wide range of subwoofers.